APPLE PHOTO ID INSTRUCTIONS
TO GET YOUR LOGO ON THE MACHINE

THIS GUIDE HAS 2 DIFFERENT VERSIONS BASED ON THE VERSION OF YOUR MACHINE. FIRST DETERMINE IF YOUR PHOTO ID IS 1.8 OR LOWER, or 1.9 OR HIGHER. THEN FOLLOW THE DIRECTIONS FOR YOUR VERSION.

FOR 1.8 OR LOWER:

Directions Installing Customs Logos

NG photo booth equipped with a Mitsubishi 9550 printer

The software that supports the Mitsubishi 9550 printer has wider capabilities …. The machine can support multiple logos that can be selected as per the occasion, or set to print randomly. In order to achieve this, logos created must have unique filenames. All logos are named logo_x.bmp where x is a number from 1 to 3. The logo cd will contain 3 directories (folders)… and directory and filesnames are critical for success.

Software Version 1.8 and below

The directory tree is as such:

C:\ TodosLogosFashion

Logo_1.bmp

Logo_2.bmp

Logo_3.bmp

C:\ TodosLogosID

Logo_1.bmp

Logo_2.bmp

Logo_3.bmp

C:\ TodosLogosFunny

Logo_1.bmp

Logo_2.bmp

Logo_3.bmp

Start by creating logos

Logo images must be Windows Bitmaps and must meet these requirements:

Fashion logo : Width : 472 pixels

Height : 596 pixels

Resolution : 72 pixels per inch

ID logo : Width: 420 pixels

Height: 520 pixels

Resolution: 72 pixels per inch

Funny logo : Width: 492 pixels

Height: 660 pixels

Resolution: 72 pixels per inch

NOTE: the Funny logo because it prints in a vertical strip must be rotated 90 degrees CCW

Create 3 folders on your hard drive…

1. TodosLogosFashion
2. TodosLogosID
3. TodosLogosFunny

Insert in each the respective logo with filename Logo_x.bmp where x is a number from 1 to 3 into the appropriate folder

Take the completed set and burn the 3 folders to cd:

Take the cd to the machine and insert it into the dvd drive

Press the yellow configuration button>

Press the green “ok” button until the option “costumise” is highlighted in red>

Press the right arrow button on the control panel until the logo option reads “yes” or “random” (depending on your desire)

Press the red “X” button until the machine reboots>

When the machine restarts:

Press the configuration button

Press the green button until “check logo fashion” is highlighted in red
On the screen you should see the logo you created displayed on screen… and it will print in the fourth position of the strip

_______________________________________________________________________

**********************
FOR 1.9 AND UP:

Directions Installing Customs Logos

NG photo booth equipped with a Mitsubishi 9550 printer

The software that supports the Mitsubishi 9550 printer has wider capabilities …. The machine can support multiple logos that can be selected as per the occasion, or set to print randomly. In order to achieve this, logos created must have unique filenames. All logos are named logo_x.bmp where x is a number from 1 to 3. The logo cd will contain 3 directories (folders)… and directory and filesnames are critical for success.

Software Version 1.9 and up

The directory tree is as such:

C:\ AlllogosFashion

Logo_1.bmp

Logo_2.bmp

Logo_3.bmp

C:\ AlllogosID

Logo_1.bmp

Logo_2.bmp

Logo_3.bmp

C:\ AlllogosFunny

Logo_1.bmp

Logo_2.bmp

Logo_3.bmp

Start by creating logos

Logo images must be Windows Bitmaps and must meet these requirements:

Fashion logo : Width : 472 pixels

Height : 596 pixels

Resolution : 72 pixels per inch

ID logo : Width: 420 pixels

Height: 520 pixels

Resolution: 72 pixels per inch

Funny logo : Width: 492 pixels

Height: 660 pixels

Resolution: 72 pixels per inch

NOTE: the Funny logo because it prints in a vertical strip must be rotated 90 degrees CCW

Create 3 folders on your hard drive…

1. AlllogosFashion
2. AlllogosID
3. AlllogosFunny

Insert in each the respective logo with filename Logo_x.bmp where x is a number from 1 to 3 into the appropriate folder

Take the completed set and burn the 3 folders to cd:

Take the cd to the machine and insert it into the dvd drive

Press the yellow configuration button>

Press the green “ok” button until the option “customize” is highlighted in red>

Press the right arrow button on the control panel until the logo option reads “yes” or “random” (depending on your desire)

Press the red “X” button until the machine reboots>

When the machine restarts:

Press the configuration button

Press the green button until “check logo fashion” is highlighted in red

On the screen you should see the logo you created displayed on screen… and it will print in the fourth position of the strip